Intel

Cyclone® V GX Field Programmable Gate Array (FPGA) IC 240 14251008 301000 484-FBGA

Summary of Features for Cyclone V Devices

Technology

• TSMC's 28-nm low-power (28LP) process technology

• 1.1 V core voltage

Packaging

• Wirebond low-halogen packages

• Multiple device densities with compatible package footprints for seamless migration between

different device densities

• RoHS-compliant and leaded(1)options

High-performance FPGA fabric

Enhanced 8-input ALM with four registers

Internal memory blocks

• M10K—10-kilobits (Kb) memory blocks with soft error correction code (ECC)

• Memory logic array block (MLAB)—640-bit distributed LUTRAM where you can use up to 25%

of the ALMs as MLAB memory

Embedded Hard IP blocks

Variable-precision DSP

• Native support for up to three signal processing precision levels

(three 9 x 9, two 18 x 18, or one 27 x 27 multiplier) in the same

variable-precision DSP block

• 64-bit accumulator and cascade

• Embedded internal coefficient memory

• Preadder/subtractor for improved efficiency

Memory controller

DDR3, DDR2, and LPDDR2 with 16 and 32 bit ECC support

Embedded transceiver I/O

PCI Express* (PCIe*) Gen2 and Gen1 (x1, x2, or x4) hard IP with

multifunction support, endpoint, and root port

Clock networks

• Up to 550 MHz global clock network

• Global, quadrant, and peripheral clock networks

• Clock networks that are not used can be powered down to reduce dynamic power

Phase-locked loops (PLLs)

• Precision clock synthesis, clock delay compensation, and zero delay buffering (ZDB)

• Integer mode and fractional mode

FPGA General-purpose I/Os (GPIOs)

• 875 megabits per second (Mbps) LVDS receiver and 840 Mbps LVDS transmitter

• 400 MHz/800 Mbps external memory interface

• On-chip termination (OCT)

• 3.3 V support with up to 16 mA drive strength

Low-power high-speed serial interface

• 614 Mbps to 6.144 Gbps integrated transceiver speed

• Transmit pre-emphasis and receiver equalization

• Dynamic partial reconfiguration of individual channels

HPS(Cyclone V SE, SX,and ST devices only)

• Single or dual-core Arm Cortex-A9 MPCore processor-up to 925 MHz maximum frequency with

support for symmetric and asymmetric multiprocessing

• Interface peripherals—10/100/1000 Ethernet media access control (EMAC), USB 2.0

On-The-GO (OTG) controller, quad serial peripheral interface (QSPI) flash controller, NAND

flash controller, Secure Digital/MultiMediaCard (SD/MMC) controller, UART, controller area

network (CAN), serial peripheral interface (SPI), I2C interface, and up to 85 HPS GPIO

interfaces

• System peripherals—general-purpose timers, watchdog timers, direct memory access (DMA)

controller, FPGA configuration manager, and clock and reset managers

• On-chip RAM and boot ROM

• HPS–FPGA bridges—include the FPGA-to-HPS, HPS-to-FPGA, and lightweight HPS-to-FPGA

bridges that allow the FPGA fabric to issue transactions to slaves in the HPS, and vice versa

• FPGA-to-HPS SDRAM controller subsystem—provides a configurable interface to the multiport

front end (MPFE) of the HPS SDRAM controller

• Arm CoreSight™ JTAG debug access port, trace port, and on-chip trace storage

Configuration

• Tamper protection—comprehensive design protection to protect your valuable IP investments

• Enhanced advanced encryption standard (AES) design security features

• CvP

• Dynamic reconfiguration of the FPGA

• Active serial (AS) x1 and x4, passive serial (PS), JTAG, and fast passive parallel (FPP) x8 and

x16 configuration options

• Internal scrubbing (2)

• Partial reconfiguration (3)

MAX® 10 Field Programmable Gate Array (FPGA) IC 246 562176 16000 324-LFBGA

Intel® MAX® 10 FPGA Device Datasheet

This datasheet describes the electrical characteristics, switching characteristics, configuration specifications, and timing for

Intel MAX? 10 devices.

Intel MAX 10 Device Grades and Speed Grades Supported

Commercial

•–C7

• –C8 (slowest)

Industrial

• –I6 (fastest)

• –I7

Automotive

•–A6

• –A7

How to choose FPGA for your project?

Dual ARM® Cortex®-A9 MPCore™ with CoreSight™ System On Chip (SOC) IC Cyclone® V SE FPGA - 110K Logic Elements 925MHz 896-FBGA (31x31)

Summary of Features for Cyclone V Devices

Technology

• TSMC's 28-nm low-power (28LP) process technology

• 1.1 V core voltage

Packaging

• Wirebond low-halogen packages

• Multiple device densities with compatible package footprints for seamless migration between

different device densities

• RoHS-compliant and leaded(1)options

High-performance FPGA fabric

Enhanced 8-input ALM with four registers

Internal memory blocks

• M10K—10-kilobits (Kb) memory blocks with soft error correction code (ECC)

• Memory logic array block (MLAB)—640-bit distributed LUTRAM where you can use up to 25%

of the ALMs as MLAB memory

Embedded Hard IP blocks

Variable-precision DSP

• Native support for up to three signal processing precision levels

(three 9 x 9, two 18 x 18, or one 27 x 27 multiplier) in the same

variable-precision DSP block

• 64-bit accumulator and cascade

• Embedded internal coefficient memory

• Preadder/subtractor for improved efficiency

Memory controller

DDR3, DDR2, and LPDDR2 with 16 and 32 bit ECC support

Embedded transceiver I/O

PCI Express* (PCIe*) Gen2 and Gen1 (x1, x2, or x4) hard IP with

multifunction support, endpoint, and root port

Clock networks

• Up to 550 MHz global clock network

• Global, quadrant, and peripheral clock networks

• Clock networks that are not used can be powered down to reduce dynamic power

Phase-locked loops (PLLs)

• Precision clock synthesis, clock delay compensation, and zero delay buffering (ZDB)

• Integer mode and fractional mode

FPGA General-purpose I/Os (GPIOs)

• 875 megabits per second (Mbps) LVDS receiver and 840 Mbps LVDS transmitter

• 400 MHz/800 Mbps external memory interface

• On-chip termination (OCT)

• 3.3 V support with up to 16 mA drive strength

Low-power high-speed serial interface

• 614 Mbps to 6.144 Gbps integrated transceiver speed

• Transmit pre-emphasis and receiver equalization

• Dynamic partial reconfiguration of individual channels

HPS(Cyclone V SE, SX,and ST devices only)

• Single or dual-core Arm Cortex-A9 MPCore processor-up to 925 MHz maximum frequency with

support for symmetric and asymmetric multiprocessing

• Interface peripherals—10/100/1000 Ethernet media access control (EMAC), USB 2.0

On-The-GO (OTG) controller, quad serial peripheral interface (QSPI) flash controller, NAND

flash controller, Secure Digital/MultiMediaCard (SD/MMC) controller, UART, controller area

network (CAN), serial peripheral interface (SPI), I2C interface, and up to 85 HPS GPIO

interfaces

• System peripherals—general-purpose timers, watchdog timers, direct memory access (DMA)

controller, FPGA configuration manager, and clock and reset managers

• On-chip RAM and boot ROM

• HPS–FPGA bridges—include the FPGA-to-HPS, HPS-to-FPGA, and lightweight HPS-to-FPGA

bridges that allow the FPGA fabric to issue transactions to slaves in the HPS, and vice versa

• FPGA-to-HPS SDRAM controller subsystem—provides a configurable interface to the multiport

front end (MPFE) of the HPS SDRAM controller

• Arm CoreSight™ JTAG debug access port, trace port, and on-chip trace storage

Configuration

• Tamper protection—comprehensive design protection to protect your valuable IP investments

• Enhanced advanced encryption standard (AES) design security features

• CvP

• Dynamic reconfiguration of the FPGA

• Active serial (AS) x1 and x4, passive serial (PS), JTAG, and fast passive parallel (FPP) x8 and

x16 configuration options

• Internal scrubbing (2)

• Partial reconfiguration (3)

Dual ARM® Cortex®-A9 MPCore™ with CoreSight™ System On Chip (SOC) IC Cyclone® V SX FPGA - 85K Logic Elements 600MHz 896-FBGA (31x31)

Summary of Features for Cyclone V Devices

Technology

• TSMC's 28-nm low-power (28LP) process technology

• 1.1 V core voltage

Packaging

• Wirebond low-halogen packages

• Multiple device densities with compatible package footprints for seamless migration between

different device densities

• RoHS-compliant and leaded(1)options

High-performance FPGA fabric

Enhanced 8-input ALM with four registers

Internal memory blocks

• M10K—10-kilobits (Kb) memory blocks with soft error correction code (ECC)

• Memory logic array block (MLAB)—640-bit distributed LUTRAM where you can use up to 25%

of the ALMs as MLAB memory

Embedded Hard IP blocks

Variable-precision DSP

• Native support for up to three signal processing precision levels

(three 9 x 9, two 18 x 18, or one 27 x 27 multiplier) in the same

variable-precision DSP block

• 64-bit accumulator and cascade

• Embedded internal coefficient memory

• Preadder/subtractor for improved efficiency

Memory controller

DDR3, DDR2, and LPDDR2 with 16 and 32 bit ECC support

Embedded transceiver I/O

PCI Express* (PCIe*) Gen2 and Gen1 (x1, x2, or x4) hard IP with

multifunction support, endpoint, and root port

Clock networks

• Up to 550 MHz global clock network

• Global, quadrant, and peripheral clock networks

• Clock networks that are not used can be powered down to reduce dynamic power

Phase-locked loops (PLLs)

• Precision clock synthesis, clock delay compensation, and zero delay buffering (ZDB)

• Integer mode and fractional mode

FPGA General-purpose I/Os (GPIOs)

• 875 megabits per second (Mbps) LVDS receiver and 840 Mbps LVDS transmitter

• 400 MHz/800 Mbps external memory interface

• On-chip termination (OCT)

• 3.3 V support with up to 16 mA drive strength

Low-power high-speed serial interface

• 614 Mbps to 6.144 Gbps integrated transceiver speed

• Transmit pre-emphasis and receiver equalization

• Dynamic partial reconfiguration of individual channels

HPS(Cyclone V SE, SX,and ST devices only)

• Single or dual-core Arm Cortex-A9 MPCore processor-up to 925 MHz maximum frequency with

support for symmetric and asymmetric multiprocessing

• Interface peripherals—10/100/1000 Ethernet media access control (EMAC), USB 2.0

On-The-GO (OTG) controller, quad serial peripheral interface (QSPI) flash controller, NAND

flash controller, Secure Digital/MultiMediaCard (SD/MMC) controller, UART, controller area

network (CAN), serial peripheral interface (SPI), I2C interface, and up to 85 HPS GPIO

interfaces

• System peripherals—general-purpose timers, watchdog timers, direct memory access (DMA)

controller, FPGA configuration manager, and clock and reset managers

• On-chip RAM and boot ROM

• HPS–FPGA bridges—include the FPGA-to-HPS, HPS-to-FPGA, and lightweight HPS-to-FPGA

bridges that allow the FPGA fabric to issue transactions to slaves in the HPS, and vice versa

• FPGA-to-HPS SDRAM controller subsystem—provides a configurable interface to the multiport

front end (MPFE) of the HPS SDRAM controller

• Arm CoreSight™ JTAG debug access port, trace port, and on-chip trace storage

Configuration

• Tamper protection—comprehensive design protection to protect your valuable IP investments

• Enhanced advanced encryption standard (AES) design security features

• CvP

• Dynamic reconfiguration of the FPGA

• Active serial (AS) x1 and x4, passive serial (PS), JTAG, and fast passive parallel (FPP) x8 and

x16 configuration options

• Internal scrubbing (2)

• Partial reconfiguration (3)