A Comprehensive Guide To TIBPAL22V10Z-25CFN * Programmable Logic Device (PLD) IC Macrocells

* Programmable Logic Device (PLD) IC Macrocells

General Description

The CMOS PLD devices feature variable product terms, flexible outputs, and virtually zero standby power. It combines

TI's EPIC™ (Enhanced Processed Implanted CMOS) process with ultraviolet-light-erasable EPROM technology. Each

output has an output logic macrocell (OLM) configuration allowing for user definition of the output type. This device

provides reliable, low-power substitutes for numerous high-performance TTL PLDs with gate complexities between 300

and 800 gates.

The TICPAL22V10Z has 12 dedicated inputs and 10 user-definable outputs. Individual outputs can be programmed as

registered or combinational and inverting or noninverting as shown in the OLM diagram.These ten outputs are enabled

through the use of individual product terms.

The variable product-term distribution on this device removes rigid limitation to a maximum of eight product terms per

output. This technique allocates from 8 to 16 logical product terms to each output for an average of 12 product terms

per output. The variable allocation of product terms allows for far more complex functions to be implemented in this

device than in previously available devices.

With features such as the programmable OLMs and the variable product-term distribution, the TICPAL22V10Z offers

quick design and development of custom LSI functions. Since each of the ten output pins may be individually configured

as inputs on either a temporary or permanent basis, functions requiring up to 21 inputs and a single output or down to

12 inputs and 10 outputs can be implemented with this device.

Design complexity is enhanced by the addition of synchronous set and asynchronous reset product terms. These functions

are common to all registers. When the synchronous set product term is a logic 1, the output registers are loaded with a

logic 1 on the next low-to-high clock transition. When the asynchronous reset product term is a logic 1, the output

registers are loaded with a logic 0 independently of the clock. The output logic level after set or reset will depend on the

polarity selected during programming.

Output registers of this device can be preloaded to any desired state during testing, thus allowing for full logical

verification during product testing.

The TICPAL22V10Z has internal electrostatic discharge (ESD) protection circuits and has been classified with a 2000-V

ESD rating tested under MIL-STD-883C, Method 3015.6. However, care should be exercised in handling these devices, as

exposure to ESD may result in a degradation of the device parametric performance.

The floating-gate programmable cells allow the devices to be fully programmed and tested before assembly to assure

high field programming yield and functionality. They are then erased by ultraviolet light before packaging.

The TICPAL22V10Z-25C is characterized for operation from 0℃ to 75°C. The TICPAL22V10Z-30I is characterized for

operation from -40℃ to 85℃.

Design security

The’PAL22V10Z contains a programmable design security cell. Programming this cell will disable the read verify and

programming circuitry protecting the design from being copied. The security cell is usually programmed after the design

is finalized and released to production. A secured device will verify as if every location in the device is programmed.

Because programming is accomplished by storing an invisible charge instead of opening a metal link, the '22V10Z cannot

be copied by visual inspection. Once a secured device is fully erased, it can be reprogrammed to any desired configuration.

Features

• 24-Pin Advanced CMOS PLD

• Virtually Zero Standby Power

• Propagation Delay Time:

   l, 1/O to 1/O in the Turbo Mode

      -25C...25 ns Max

      -301 ...30 ns Max

   I, 1/O to 1/O in the Zero-Power Mode

      -25C ...35 ns Max

      -30l ...40 ns Max

   CLK to Q

      -25C ...15 ns Max

      -30l ...20 ns Max

• Variable Product Term Distribution Allows More Complex Functions to Be Implemented

• Each Output Is User-Programmable for Registered or Combinatorial Operation, Polarity, and Output Enable Control

• Extra Terms Provide Logical Synchronous Set and Asynchronous Reset Capability

• Preload Capability on All Registered Outputs Allow for lmproved Device Testing

• UV Light Erasable Cell Technology Allows for:

      Reconfigurable Logic

      Reprogrammable Cells

      Full Factory Testing for High

         Programming Yield

• Programmable Design Security Bit Prevents Copying of Logic Stored in Device

• Package Options Include Plastic Dual-In-Line and Clip Carrier [for One-Time-Programmable (OTP) Devices] and Ceramic

Dual-In-Line Windowed Package

How to choose FPGA for your project?