Microsemi Corporation

IGLOO Field Programmable Gate Array (FPGA) IC 81 768 132-WFQFN

General Description

The IGLOO family of flash FPGAs, based on a 130-nm flash process, offers the lowest power FPGA, a single-chip solution,

small footprint packages, reprogrammability, and an abundance of advanced features.

The Flash*Freeze technology used in IGLOO devices enables entering and exiting an ultra-low power mode that

consumes as little as 5 μW while retaining SRAM and register data. Flash*Freeze technology simplifies power management

through I/O and clock management with rapid recovery to operation mode.

The Low Power Active capability (static idle) allows for ultra-low power consumption (from 12 μW) while the IGLOO device

is completely functional in the system. This allows the IGLOO device to control system power management based on

external inputs (e.g., scanning for keyboard stimulus) while consuming minimal power.

Nonvolatile flash technology gives IGLOO devices the advantage of being a secure, low power, single-chip solution that is

Instant On. IGLOO is reprogrammable and offers time-to-market benefits at an ASIC-level unit cost.

These features enable designers to create high-density systems using existing ASIC or FPGA design flows and tools.

IGLOO devices offer 1 kbit of on-chip, reprogrammable, nonvolatile FlashROM storage as well as clock conditioning

circuitry based on an integrated phase-locked loop (PLL). The AGL015 and AGL030 devices have no PLL or RAM support.

IGLOO devices have up to 1 million system gates, supported with up to 144 kbits of true dual-port SRAM and up to 300

user I/Os.

M1 IGLOO devices support the high-performance, 32-bit Cortex-M1 processor developed by ARM for implementation in

FPGAs. Cortex-M1 is a soft processor that is fully implemented in the FPGA fabric. It has a three-stage pipeline that offers

a good balance between low power consumption and speed when implemented in an M1 IGLOO device. The processor

runs the ARMv6-M instruction set, has a configurable nested interrupt controller, and can be implemented with or

without the debug block. Cortex-M1 is available for free from Microsemi for use in M1 IGLOO FPGAs.

The ARM-enabled devices have ordering numbers that begin with M1AGL and do not support AES decryption.

Features and Benefits

• Low Power

      1.2 V to 1.5 V Core Voltage Support for Low Power

      Supports Single-Voltage System Operation

      5 μW Power Consumption in Flash*Freeze Mode

      Low Power Active FPGA Operation

      Flash*Freeze Technology Enables Ultra-Low Power Consumption while MaintainingFPGA Content

      Easy Entry to / Exit from Ultra-Low Power Flash*Freeze Mode

• High Capacity

      15K to 1 Million System Gates

      Up to 144 Kbits of True Dual-Port SRAM

      Up to 300 User 1/Os

• Reprogrammable Flash Technology

      130-nm, 7-Layer Metal, Flash-Based CMOS Process

      Instant On Level 0 Support

      Single-Chip Solution

      Retains Programmed Design When Powered Off

      250 MHz (1.5 V systems) and 160 MHz (1.2 V systems) System Performance

• In-System Programming (ISP) and Security

      ISP Using On-Chip 128-Bit Advanced Encryption Standard (AES) Decryption (except ARM®-enabled IGLOO®devices)

      via JTAG (IEEE 1532-compliant)

      FlashLock®Designed to Secure FPGA Contents

• High-Performance Routing Hierarchy

      Segmented, Hierarchical Routing and Clock Structure

• Advanced l/O

      700 Mbps DDR,LVDS-Capable I/Os (AGL250 and above)

      1.2 V, 1.5 V, 1.8 V, 2.5V, and 3.3 V Mixed-Voltage Operation

      Bank-Selectable I/O Voltages--up to 4 Banks per Chip

      Single-Ended I/O Standards:LVTTL,LVCMOS 3.3V/2.5 V/ 1.8 V /1.5 V/ 1.2 .V, 3.3 V PCI/ 3.3 V PCI-X, and LVCMOS

      2.5 V/5.0V Input

      DifferentialI/O Standards:LVPECL，LVDS，B-LVDS,and M-LVDS (AGL250 and above)

      Wide Range Power Supply Voltage Support per JESD8-B, Allowing I/Os to Operate from 2.7 V to 3.6 V

      Wide Range Power Supply Voltage Support per JESD8-12, Allowing I/Os to Operate from 1.14 V to 1.575V

      I/O Registers on Input, Output, and Enable Paths

      Hot-Swappable and Cold-Sparing,I/Os+

      Programmable Output Slew Rateand Drive Strength

      Weak Pull-Up/-Down

      IEEE 1149.1 (JTAG) Boundary Scan Test

      Pin-Compatible Packages across the IGLOO Family

• Clock Conditioning Circuit(CCC) and PLL

      Six CCC Blocks, One with an Integrated PLL

      Configurable Phase Shift, Multiply/Divide,Delay Capabilities, and External Feedback

      Wide Input Frequency Range (1.5 MHz up to 250 MHz)

• Embedded Memory

      1 kbit of FlashROM User Nonvolatile Memory

      SRAMs and FIFOs with Variable-Aspect-Ratio4,608-Bit RAM Blocks (x1,x2,x4, x9, and x18 organizations)

      True Dual-Port SRAM (except x18)

• ARM Processor Support in IGLOO FPGAs

      M1 IGLOO Devices--Cortex®-M1 Soft Processor Available with or without Debug

How to choose FPGA for your project?

PDF

IGLOO Field Programmable Gate Array (FPGA) IC 68 36864 6144 100-TQFP

General Description

The IGLOO family of flash FPGAs, based on a 130-nm flash process, offers the lowest power FPGA, a single-chip solution,

small footprint packages, reprogrammability, and an abundance of advanced features.

The Flash*Freeze technology used in IGLOO devices enables entering and exiting an ultra-low power mode that

consumes as little as 5 μW while retaining SRAM and register data. Flash*Freeze technology simplifies power management

through I/O and clock management with rapid recovery to operation mode.

The Low Power Active capability (static idle) allows for ultra-low power consumption (from 12 μW) while the IGLOO device

is completely functional in the system. This allows the IGLOO device to control system power management based on

external inputs (e.g., scanning for keyboard stimulus) while consuming minimal power.

Nonvolatile flash technology gives IGLOO devices the advantage of being a secure, low power, single-chip solution that is

Instant On. IGLOO is reprogrammable and offers time-to-market benefits at an ASIC-level unit cost.

These features enable designers to create high-density systems using existing ASIC or FPGA design flows and tools.

IGLOO devices offer 1 kbit of on-chip, reprogrammable, nonvolatile FlashROM storage as well as clock conditioning

circuitry based on an integrated phase-locked loop (PLL). The AGL015 and AGL030 devices have no PLL or RAM support.

IGLOO devices have up to 1 million system gates, supported with up to 144 kbits of true dual-port SRAM and up to 300

user I/Os.

M1 IGLOO devices support the high-performance, 32-bit Cortex-M1 processor developed by ARM for implementation in

FPGAs. Cortex-M1 is a soft processor that is fully implemented in the FPGA fabric. It has a three-stage pipeline that offers

a good balance between low power consumption and speed when implemented in an M1 IGLOO device. The processor

runs the ARMv6-M instruction set, has a configurable nested interrupt controller, and can be implemented with or

without the debug block. Cortex-M1 is available for free from Microsemi for use in M1 IGLOO FPGAs.

The ARM-enabled devices have ordering numbers that begin with M1AGL and do not support AES decryption.

Features and Benefits

• Low Power

      1.2 V to 1.5 V Core Voltage Support for Low Power

      Supports Single-Voltage System Operation

      5 μW Power Consumption in Flash*Freeze Mode

      Low Power Active FPGA Operation

      Flash*Freeze Technology Enables Ultra-Low Power Consumption while MaintainingFPGA Content

      Easy Entry to / Exit from Ultra-Low Power Flash*Freeze Mode

• High Capacity

      15K to 1 Million System Gates

      Up to 144 Kbits of True Dual-Port SRAM

      Up to 300 User 1/Os

• Reprogrammable Flash Technology

      130-nm, 7-Layer Metal, Flash-Based CMOS Process

      Instant On Level 0 Support

      Single-Chip Solution

      Retains Programmed Design When Powered Off

      250 MHz (1.5 V systems) and 160 MHz (1.2 V systems) System Performance

• In-System Programming (ISP) and Security

      ISP Using On-Chip 128-Bit Advanced Encryption Standard (AES) Decryption (except ARM®-enabled IGLOO®devices)

      via JTAG (IEEE 1532-compliant)

      FlashLock®Designed to Secure FPGA Contents

• High-Performance Routing Hierarchy

      Segmented, Hierarchical Routing and Clock Structure

• Advanced l/O

      700 Mbps DDR,LVDS-Capable I/Os (AGL250 and above)

      1.2 V, 1.5 V, 1.8 V, 2.5V, and 3.3 V Mixed-Voltage Operation

      Bank-Selectable I/O Voltages--up to 4 Banks per Chip

      Single-Ended I/O Standards:LVTTL,LVCMOS 3.3V/2.5 V/ 1.8 V /1.5 V/ 1.2 .V, 3.3 V PCI/ 3.3 V PCI-X, and LVCMOS

      2.5 V/5.0V Input

      DifferentialI/O Standards:LVPECL，LVDS，B-LVDS,and M-LVDS (AGL250 and above)

      Wide Range Power Supply Voltage Support per JESD8-B, Allowing I/Os to Operate from 2.7 V to 3.6 V

      Wide Range Power Supply Voltage Support per JESD8-12, Allowing I/Os to Operate from 1.14 V to 1.575V

      I/O Registers on Input, Output, and Enable Paths

      Hot-Swappable and Cold-Sparing,I/Os+

      Programmable Output Slew Rateand Drive Strength

      Weak Pull-Up/-Down

      IEEE 1149.1 (JTAG) Boundary Scan Test

      Pin-Compatible Packages across the IGLOO Family

• Clock Conditioning Circuit(CCC) and PLL

      Six CCC Blocks, One with an Integrated PLL

      Configurable Phase Shift, Multiply/Divide,Delay Capabilities, and External Feedback

      Wide Input Frequency Range (1.5 MHz up to 250 MHz)

• Embedded Memory

      1 kbit of FlashROM User Nonvolatile Memory

      SRAMs and FIFOs with Variable-Aspect-Ratio4,608-Bit RAM Blocks (x1,x2,x4, x9, and x18 organizations)

      True Dual-Port SRAM (except x18)

• ARM Processor Support in IGLOO FPGAs

      M1 IGLOO Devices--Cortex®-M1 Soft Processor Available with or without Debug

How to choose FPGA for your project?

PDF

ProASIC3L Field Programmable Gate Array (FPGA) IC 157 36864 256-LBGA

Clock Frequency Synthesis

Deriving clocks of various frequencies from a single reference clock is known as frequency synthesis.The PLL has an input

frequency range from 1.5 to 350 MHz. This frequency is automatically divideddown to a range between 1.5 MHz and

5.5 MHz by input dividers (not shown in Figure 4-19 on page 100)between PLL macro inputs and PLL phase detector

inputs. The VCO output is capable of an outputrange from 24 to 350 MHz. With dividers before the input to the PLL core

and following the VCO outputs,the VCO output frequency can be divided to provide the final frequency range from 0.75

to 350 MHz.Using SmartGen, the dividers are automatically set to achieve the closest possible matches to thespecified

output frequencies.

Users should be cautious when selecting the desired PLL input and output frequencies and the I/O bufferstandard used

to connect to the PLL input and output clocks. Depending on the I/O standards used forthe PLL input and output clocks,

the I/O frequencies have different maximum limits. Refer to the familydatasheets for specifications of maximum I/O

frequencies for supported I/O standards. Desired PLL inputor output frequencies will not be achieved if the selected

frequencies are higher than the maximum I/Ofrequencies allowed by the selected I/O standards. Users should be careful

when selecting the I/Ostandards used for PLL input and output clocks. Performing post-layout simulation can help detect

thistype of error, which will be identified with pulse width violation errors. Users are strongly encouraged toperform

post-layout simulation to ensure the I/O standard used can provide the desired PLL input oroutput frequencies. Users can

also choose to cascade PLLs together to achieve the high frequenciesneeded for their applications. Details of cascading

PLLs are discussed in the "Cascading CCCs" sectionon page 125.

In SmartGen, the actual generated frequency (under typical operating conditions) will be displayedbeside the requested

output frequency value. This provides the ability to determine the exact frequencythat can be generated by SmartGen, in

real time. The log file generated by SmartGen is a useful tool indetermining how closely the requested clock frequencies

match the user specifications. For example,assume a user specifies 101 MHz as one of the secondary output frequencies.

If the best outputfrequency that could be achieved were 100 MHz, the log file generated by SmartGen would indicate

theactual generated frequency

How to choose FPGA for your project?

PDF

EX Field Programmable Gate Array (FPGA) IC 56 128 100-LQFP

General Description

The eX family of FPGAs is a low-cost solution for low-power, high-performance designs. The inherent low power

attributes of the antifuse technology, coupled with an additional low static power mode, make these devices ideal for

power-sensitive applications. Fabricated with an advanced 0.22 mm CMOS antifuse technology, these devices achieve

high performance with no power penalty.

Features and Benefits

• Leading Edge Performance

      240 MHz System Performance

      350 MHz Internal Performance

      3.9 ns Clock-to-Out (Pad-to-Pad)

• Specifications

      3,000 to 12,000 Available System Gates

      Maximum 512 Flip-Flops (Using CC Macros)

      0.22 µm CMOS Process Technology

      Up to 132 User-Programmable I/O Pins

• Features

      High-Performance, Low-Power Antifuse FPGA

      LP/Sleep Mode for Additional Power Savings 

      Advanced Small-Footprint Packages

      Hot-Swap Compliant I/Os

      Single-Chip Solution

      Nonvolatile

      Live on Power-Up

      No Power-Up/Down Sequence Required for Supply

• Voltages

      Configurable Weak-Resistor Pull-Up or Pull-Down for

• Tristated Outputs during Power-Up

      Individual Output Slew Rate Control

      2.5 V, 3.3 V, and 5.0 V Mixed-Voltage Operation with 5.0V Input Tolerance and 5.0V Drive Strength

      Software Design Support with Microsemi Designer and Libero® Integrated Design Environment (IDE) Tools

      Up to 100% Resource Utilization with 100% Pin Locking 

      Deterministic Timing

      Unique In-System Diagnostic and Verification Capability

• with Silicon Explorer II

      Boundary Scan Testing in Compliance with IEEE

• Standard 1149.1 (JTAG)

      Fuselock™ Secure Programming Technology Designed to Prevent Reverse Engineering and Design Theft

How to choose FPGA for your project?

PDF